Sort By
Per Page
View
Grid
List
2'' Blade for Clifton No.4 & 5 Bench Plane
2'' blade to fit the Clifton No.4 smoothing plane, and the No.5 jack plane.
The Clifton bench plane blades are made from O1 steel that has been cryogenically treated to give a hardness of 60 to 62 Rockwell C. 3.6mm thick.
2'' (50mm) wide.
Made in Sheffield, UK
Bad Axe Frame Saw and Kerfing Plane Hardware Kit (no wood)
What's included.....
30 1/2" Saw Plate and 10" Kerfing Plane Plate. Blue Tempered 1095 Spring Steel. Hammer-set and sharpened by hand.
Two brackets (with kerf pre-cut), one of which is tapped for the 3/8" eye bolt.
3" x 3/8" eyebolt with jam nut.
Striker Plate with fastening screws.
Two U-bolts to secure plate to brackets.
''All you have to do is cut and form the wooden components.''
Blade for Veritas Flat & Round Spokeshaves
Replacement PM-V11 blade to fit both the Veritas Flat (05P3373) and Round (05P3374) Spokeshaves.
Blue Spruce Honing Guide
The new Blue Spruce Honing Guide turns the traditional honing guide design upside down and clamps the chisel from above, rather than below. And, while most honing guides have the roller directly under the clamp, the Blue Spruce Honing Guide wheels are offset. The Honing Guide will fit chisels and plane blades from 1/8" to 1-1/2", while Blue Spruce Bench Chisels, Butt Chisels, Dovetail Chisels...
Blue Spruce Router Plane
Whether you rely on hand tools or prefer machinery, there are times when a joint needs just a slight adjustment. Machines struggle with removing a ''little bit'', and even many hand tools fall short. That’s where a router plane shines.
The Blue Spruce engineering team studied router planes from the late 1800s to today, designing a tool that appeals to both dedicated hand-tool...
Carving the Traditional Greenman with Mary May
Variations of the Greenman motif are found in many cultures around the world. Often related to natural vegetative deities, the Greenman is a symbol of rebirth and the cycle of growth each spring. Mary May uses the Greenman project to demonstrate a variety of carving techniques, with special emphasis on carving facial features.
Mary May is a professional woodcarver in Charleston, SC, who specializes...
Flexcut 5/16'' (8mm) Scorp KN23
Scorps are essentially right-angled gouges designed for carving areas where the full length of a gouge will not fit. Knife carvers will find them useful for hollowing deep, narrow cavities. Right and left-handed models are available.
Right-Handed carvers should choose a right-handed tool to cut towards yourself. Choose a left-handed tool to cut away from yourself. 3 additional profiles available.
Flexcut Whittlin' Jack JKN88
Designed for all outdoors people. The ultimate for portability. Whittlin' Jack features a 1½'' Detail Knife and a 2'' Roughing Knife.
It weighs in at just 3oz and is just over 4'' long when closed, so it neatly fits in your pocket.
Blades do not lock in place.
Gomtaro 300 Saw
The Silky Gomtaro is a traditional straight bladed pruning saw.
It is one of the most popular and longest standing Silky saws and is widely used by professionals and serious amateurs alike for the general pruning of medium to large size branches. We know it is also used by Kuksa makers!
Gomtaro saws have a teeth configuration of 8 teeth per 30mm for a smooth finish when cutting dryer and/or...
Replacement PM-V11 Blade for the Veritas Shop Knife
Made of PM-V11 tool steel , this replacement blade for the Veritas Shop Knife is 3/32" thick and about 3/8" wide with a 55° spear-point tip. Ground to a keen edge at a 25° bevel angle.
Robert Sorby Full Round Scraper Cutter
The Robert Sorby Full Round Scraper Cutter is the perfect circular cutter for all general and large purpose hollow form turning. An incredible all rounder this cutter, like all full round cutters, provides the opportunity to rotate a couple of times to provide a clean sharp edge before it requires sharpening.
The perfect accompaniment for the Robert Sorby Hollowmaster the tool it was designed for...
Saburrtooth 1/4'' Burrs Set - Fine
This set of burrs from Saburrtooth includes:
14BN14 - Ballnose, head diameter 1/4" and head length 1 3/4"
14F12 - Flame, head diameter 1/2" and head length 3/4"
14S58 - Sphere, 5/8" diameter
14C12 - Cylinder, head diameter 1/2" and head length 3/4"
14T14 - Taper, head diameter 1/4" and head length 1 3/8"
14RS34 - Rotosaw, head diameter 3/4"...
Saburrtooth 1/4'' Cylinder - 1/4'' x 1 3/4''
Head Diameter: 1/4"
Head Length: 1¾"
Saburrtooth 1/4'' Dove Tail 3/4'' x 1 1/4''
15% discount from price shown.
Saburrtooth 1/4'' Taper 3/4'' x 1 1/4''
15% discount from price shown.
Saburrtooth 1/8'' Cylinder - 1/2'' x 1/2'' - (Radius End)
15% discount from price shown.
Tormek Hand Tool Kit
This Tormek Hand Tool kit includes all the jigs you need for sharpening your knives, scissors, draw knives, small knives, flexible knives and axes as well as short chisel and carving tools. The perfect kit to sharpen all your hand tools.
The jigs are packed in a TC-800 Tormek Case with the included HTK-00 Storage Tray. The Tormek Case keeps your jigs and accessories organized and is easy to carry...
Traditional Moulding Techniques: The Basics
with Don McConnell
Have you ever wanted to match a molding on an heirloom, or make your own profile without having to get a custom-made shaper head? Hand cut your own complex, classic moldings with simple hollows and rounds. Don McConnell shows you how, from layout to finish molding.
80 Minutes, DVD. Lie-Nielsen Toolworks Productions, 2007.
Veritas Optional Depth Stop for Small Router Plane
This optional stainless-steel depth stop is for use with the Veritas Small Router Plane. To limit cutting depth to a preset maximum, the stop clamps onto the blade shaft.
Made in Canada.
Henry Taylor No. 1 Allongee Chisel - 1 1/4'' (32mm)
These tools were created especially for sculptors who work in large sections of timber.
They are beautifully balanced to handle heavy duty cuts as required and are fitted with heavy duty double hooped handles with shock absorbing leather washers.
Robert Sorby Curved Scraper
The curved end profileof thie Robert Sorby Scraper makes this excellent for creating, smoothing and blending curved surfaces in bowl and spindle work, eg round bottomed boxes. This new tool is able to take an agressive cut, whilst retaining the butterfly sensitivity for the refining cuts.
3/4" Curved Scraper - 16" with handle
Veritas Small Scraping Plane
The Veritas Small Scraping Plane is a great tool for the final smoothing of small, flat surfaces, even highly figured timber, or small areas of difficult grain within a larger surface.
The scraping plane comes into action after the surface has been prepared as well as possible using a finely tuned smoothing plane. What the scraping plane does is to replace the need for sanding prior to applying...
Glenn Lucas Heavy Duty Bowl Roughing Gouge
The Glenn Lucas 3/4'' Heavy Duty Bowl Roughing Gouge with a 16" handle.
Ideal for rough shaping of unseasoned wood.
The gouge features a secondary bevel on the heel to give the tool some clearance when going around tight corners making concave curves or coves.
Oscar Rush Side Axe - Left Grind
A hand forged, 130mm - 135mm (5 1/4'') edge side axe. LEFT grind.
The head weight is approximately 775g.
Handle - 320mm long (just over 1'') hand carved, faceted, kin dried ash handle.
The leather cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
This axe has been carefully designed as an all rounder rather than...
Pfeil Large Straight Drawknife
This Pfeil Straight Drawshave comes with a goatskin case and has cherry handles.
The blade is 250mm in length and the overall length is 440mm.
Classic carpenters design with straight back and straight blade.
Robert Sorby Tool Rest for Thread Cutting
The Robert Sorby Tool Rest for thread cutting provides extra control when creating internal threads.
Roughing Blade for Lie-Nielsen No. 4 and 5 Planes
A blade with a cambered edge for the No.4 and No.5 planes. Used for thicknessing boards.
Bessey GH All Steel Lever Clamps
* Greater reserves of power‚ thanks to optimised rail profile‚ for even clamping force build-up‚ especially under maximum utilisation of the clamping range
* Non-slip trigger release
* Quick - up to 5 x faster than regular clamps
* Secure - vibration resistant
* Strong - clamping force up to 8‚500 N
GH20 Opening 200mm Depth 100mm
Norton 4000/8000 Combination Waterstone
These combination waterstones offer good combination of grits for occasional sharpening.
They are supplied with excellent written instructions and plastic storage cases.
Norton Prep Stone
An artificial stone used for raising a slurry on fine grit finishing waterstones. The slurry is what does the cutting and polishing and the prep stone speeds up the slurry-making. After wetting the waterstone, rub it evenly with the prep stone which will create the slurry, even off the high spots and make for less frequent flattening of the waterstones.
Replacement Blade for Nakaya Ryoba 240mm Folding Saw
Blade 0.5mm thick
Spacing Cross Cut 1.66mm
Spacing Rip Cut 2.62-4mm
Henry Taylor Outcannel Firmer Gouges - Set of 6
Henry Taylor standard length carpenters chisels with gouge shaped blades. Outcannel gouges are ground on the outside face which creates an inside cutting edge. The blades are about about 4" (100mm) long and have stained beech rounded handles with brass ferrules.
Made in Sheffield, England for over 150 years.
Blade about 4" long.
F17 - 1/4" (6mm)
F18 - 3/8" (9mm)
F19...
Arbortech Mini Turbo Blade Kit
The Arbortech Mini TURBO Kit is a revolution in wood sculpting. This unique tool is designed to fit the Arbortech Mini Carver and most 100mm or 115mm angle grinders using the supplied extension adaptor.
The blade is precision machined from high quality steel and fitted with wo tungsten carbide teeth. The cutting teeth are rotatable, resharpenable and replaceable but it maybe some time before replacements...
Flexcut Mini Chip Knife KN20
The Flexcut Mini Chip carving knife has a 5/8" ultra thin blade, making unwanted chipping in delicate cuts less likely. The smaller handle is faceted with multiple control points to allow them to be held in a variety of comfortable positions.
Kutzall 3 Piece Coarse 1/4'' Burr Kit
Kutzall burrs are the perfect companions for your rotary carving tools.
Made in the USA, Kutzall burrs provide a great combination of material removal and surface quality. Efficient with or against the grain, these burrs have a long wear life.
Their outstanding performance on a wide variety of materials to include wood, plastic, rubber, fibreglass and soft stone.
NOTE: These burrs should only...
Toothed Blade for Lie-Nielsen No. 60 1/2 Block Plane
Lie-Nielsen toothed blades have small chisel-like teeth .030" (.762mm) wide, and spaced .030" apart. They are used for heavy stock removal in difficult grain. Follow this with a fine-set Smoothing Plane.
Toothed blades are great for quick, heavy stock removal. However, something like a knot in pine can break the teeth so be careful around difficult spots. We recommend that you hone your...
Spare Blade for Lie-Nielsen Large Router Plane
Replacement blade for the No. 71 Large Router Plane.
* 3/8" square tip
* O1 Tool Steel
Note: Blade does not work in vintage Stanley planes
30mm Replacement Cutter for Arbortech Ball Gouge
This cutter is for the Arbortech Ball Gouge.
The Arbortech Ball Gouge is a unique tool designed for power carving. It has a cutting ring on a 30mm spherical ball with a 90mm arm that attaches to any standard 100mm (4") or 115mm (4½") angle grinder. The cutting action produces fine shavings rather than dust.
This ball gouge gives you the ability to make smooth hollows and concave recesses...
Flexcut No.11 Sweep Veining Gouges
The Flexcut No.9 Sweep Gouges are interchangeable blades with a steep curved cutting edge. These unhandled gouges are compatible with the SK100 Quick Connect ABS Handle, SK102 Quick Connect Palm Handle, SK103 Quick Connect Long Handle for carving by hand; and the SK109 Universal Adapter for power carving.
Available Widths:
1/16" (2mm) SK602
1/8" (3mm) SK309
3/16" (5mm)...
Flexcut Scraper Set SK121
These Flexcut scrapers are easy to use (even for children) and come ready to use.
There are 6 different profiles in the set. Once inserted into the handle any side can be used as a scraping edge.
In just a few strokes you can remove any uneven surface or finish from your work without the use of sandpaper. No airborne dust! The scrapers can remove rough areas e.g on hand or power carving or ripple...
Five Crows - Greetings Card
Five Crows is an image of one of Fiona Kingdon's creations which has been printed on 300gsm card and blank inside for your own greeting.
21cm x 10cm (DL)
Flexcut Hip Knife KN30
The Flexcut Hip Knife is a versatile fine cutting tool that is capable of a wide range of woodcarving projects. Its high-carbon steel blade is precision machined and honed ready for use. The knife is supplied in a real leather sheath that easily attaches to your belt.
Robert Sorby Set of 5 Octagonal Handled Bevel Edged Chisels
Robert Sorby Set of 5 Octagonal boxwood handled Bevel Edge Chisels with brass ferule and leather washer in a cardboard presentation box.
Includes 1/4'', 3/8'', 1/2'', 3/4'' and 1'' chisels
Overall Size 265 - 340mm
Blade Length 127 - 178mm
Lynx Quadrant Scraper Set
This Lynx Quadrant Scraper Set is the perfect solution for scraping various quadrant areas and has the benefit of the straight edge to get into corners, which sanding cannot always do.
This two piece set has the following quadrant sizes cut from the scraper:
Scraper 1 - 1/8", 3/16", 1/4", 5/16"
Scraper 2 - 3/8", 7/16", 1/2", 5/8"
These are pefect for...
Arbortech Pad for Heavy Duty Abrasive Discs
This Arbortech Backing Pad fits the Contour Sander, Mini Turbo Kit and Mini Carver. The backing pad is made from rubber and has flexible edges to allow the pad to follow the curvature of your work.
They are used in conjunction with Arbortech 50mm Heavy Duty Abrasive Discs.
Henry Taylor Woodcarving Punch - 6 x 2 Dots
Woodcarvers Punches from Henry Taylor which are made here in the UK. They are approximately 75mm (3'') in length and approximately 5mm wide.
.png "Last Ones!")
Saburrtooth 6mm Sphere - 5/8' x 5/8''
15% discount from price shown.
Tormek DC-200 Diamond Wheel Coarse 360G
The Tormek Diamond Wheel Coarse has a grit size of 360 for fast steel removal when shaping and a rapid repair of a dull or damaged edge.
You can sharpen all types of material, including steel, ceramic and carbide. Fits Tormek T-4 Original and Tormek T-4 Bushcraft.
Included with every diamond wheel is a bottle of Tormek Anti-Corrosion Concentrate. Always use the concentrate in the water when sharpening...