Sort By
Per Page
View
Grid
List
Bad Axe Frame Saw and Kerfing Plane Hardware Kit (no wood)
What's included.....
30 1/2" Saw Plate and 10" Kerfing Plane Plate. Blue Tempered 1095 Spring Steel. Hammer-set and sharpened by hand.
Two brackets (with kerf pre-cut), one of which is tapped for the 3/8" eye bolt.
3" x 3/8" eyebolt with jam nut.
Striker Plate with fastening screws.
Two U-bolts to secure plate to brackets.
''All you have to do is cut and form the wooden components.''
Barr 7/8'' Corner Chisel
Corner chisels are forged from tough carbon steel; these chisels are hand-tapered, bent to 90 degrees, then flat ground.
Terrific for cleaning out mortises.
7/8" (22.225mm) x 7/8" (22.225mm) x 18" (450mm)
Barr Bench Chisels
The bench chisel has the same quality construction as their popular framing chisels, but with a shorter blade length.
The chisels are all 13" (325mm) long overall.
Available as 1" (25mm), 1½" (38mm), 2" (50mm) or as a set of 3 Bench Chisels.
Barr Fat Boy Slick
If you need a big slick for paring, this is the one! The curved edge skives into the material lessening the initial force needed to start your cut.
3½" cutting edge, 7½" blade length, 16" from edge to end of socket, length with handle 30".
Barr Framing Chisels
Barr's framing chisels have become the first choice of professional timber framers and homebuilders. These chisels will take and hold a superior edge saving you time and giving you the best possible results. Hand forged from carbon steel with a flat back and socket handle, they are a must for mortise and tenon work.
The chisels are all 17½" (438mm) long overall.
Available as 1" (25mm), 1½" (38mm),...
Barr Hand Adze
The Barr Hand Adze is the best choice for roughing out your bowls and chair seats. Designed for maximum control the 2¼" cutting edge is just enough for the task at hand. Not too light, not too heavy it is the perfect addition to your workshop!
2¼" cutting edge, head length 8", total weight 2lbs, handle length 15"
Barr Large Slick
This large slick will take on the toughest jobs with ease. They take and hold a fine edge without being brittle. The handle angles up away from your work surface to allow hand clearance. If you are fed up with poor quality slicks, try one of these. Like all Barr tools, your satisfaction is guaranteed or your money back.
2½" cutting edge, 7½" blade length, length from cutting edge to end of socket...
Barr Scarf Slick
Invaluable for cutting scarf joints on your timber projects, this slick is a favorite among log and timber smiths. It is also well-suited for cleaning up adzed timbers. Barr's scarf slick has a mild sweep with a curved edge and will give you a slight concave cut.
3½" cutting edge, 7½" blade length, 16" from edge to end of socket, length with handle 30".
Please note that this slick is not flat (by...
Barr Small Slick
Built with the same fine construction as the large slick, the small slick has a 5" blade length making it a little less hefty.
2½" cutting edge, 5½" blade length, length from cutting edge to end of socket 12", length with handle 26
Connells Chisel Guard Set 2 - Large
Set contains the following leather chisel guards: 2 x 3-3/8", 2 x 2-3/8", 2 x 2''
Connells Small Chisel Guard Set 1
Set contains the following leather chisel guards: 2 x 2", 2 x 1¼", 2 x 1", 2 x ¾", 6 x ½''
Crucible Lump Hammer
The Crucible lump hammer has a 2.2lb. hardened steel head and is ideal for assembly, mortising, setting holdfasts and dozens of other chores. Comfortable octagonal hickory handle with a waxed finish.
The late, great furniture maker Alan Peters often said that one of his favourite tools was his “lump hammer,” a British term for what Americans might call an engineer’s hammer or a small sledge....
Famag Lewis Auger Bits
Famag Lewis Auger Bits in two lengths.
Overall Length 235mm Spiral Length 160mm
Overall Length 460mm Spiral Length 380mm
A "Lewis" pattern consists of a main self tapping thread which pulls the bit through the cut and two cutting edges.
This version has a stepped head and is used for drilling deep holes in soft wood and European hard wood with power drill and joinery machines.
Due...
Fisch Adapter to Auger Bit
There are 3 different adapters for the Elite Black Augur Bits -
- Mafell
- MKII
- SDS
Fisch Elite Black Auger Bit Set of 5
The Fisch sets of 5 auger bits are available in 2 lengths, 235mm and 320mm.
These German manufactured auger bits have an enviable reputation for superior quality.
Auger bits to satisfy demand from our discerning and growing customer base.
Fisch Elite Black auger bits have a corrosion resistant coating that results in lower friction when drilling. This means deeper, faster drilling.
For...
Fisch Elite Black Auger Bit Set of 6
Fisch sets of 6 Elite Black Auger Bits available in 2 lengths, 460mm and 650mm.
These German manufactured auger bits have an enviable reputation for superior quality.
Auger bits to satisfy demand from our discerning and growing customer base.
Fisch Elite Black auger bits have a corrosion resistant coating that results in lower friction when drilling. This means deeper, faster drilling.
For...
Fisch Elite Black Auger Bits
These German manufactured auger bits have an enviable reputation for superior quality.
Auger bits to satisfy demand from our discerning and growing customer base.
Fisch Elite Black auger bits have a corrosion resistant coating that results in lower friction when drilling. This means deeper, faster drilling.
For deep drilling in all soft, hard, exotic and moist woods
"Sharp-Grip"...
Fisch Extension to Elite Black Auger Bit
Extensions for the Fisch Elite Black Auger Bits available in 2 diameters, 20mm and 26mm
Gransfors Bruk Carpenter's Axe 465
These axes have a straight edge and thin blade with low angle of the bevel face, suited for work in dry wood. The forged inward curve from the heel to the lip of the head allows your hand to grip almost straight above the centre of the edge. This, and the long straight cutting edge, gives rigidity, stability, and control when cutting. Functions like a good heavy knife. The axe poll is ground and...
Gransfors Bruk Swedish Broad Axes
The pattern of the Gransfors Broad Axe and the handle is based on old Swedish logging techniques for squaring logs and structural timbers of all kinds. Has sufficient space between the "blade’s beard" and the handle for the user’s fingers. There are different options of bevels (double, left or right). You also have handle options of straight (so the blade is in line with the...
Gransfors Bruk Swedish Drawknife 486
This is a big beast and popular for quick removal of bark from logs and other large trimming work. The hickory handles are set on full-length tangs extending straight out from the ends of the blade. The blade is bowed up and curved forward in the centre for effective peeling, shaping and smoothing. The total length is 22½". The blade is 11½" in length and 1½" wide. It weighs 1lb. 5oz. The tool...
Gyokucho Razorsaw Seiun Saku Ryoba 300mm
Full Name : Gyokucho Razorsaw Seiun Saku Ryoba.
Blade Length : 300mm.
Overall Length : 695mm Rattan / 675mm TPE.
Max Cutting Depth : N/A.
Teeth Pitch / TPI : Crosscut 3.0mm / 8.5. Rip Cut 5.6-3.5mm / 4.5-7.3.
Blade Thickness : 0.7mm.
Cutting Width : 1.10mm.
Teeth Pattern : Crosscut & Rip Cut.
Gyokucho Product Number : 616 Rattan / 664 TPE.
Weight : 350g Rattan / 415g TPE.
Replacement...
Henry Taylor Heavy Duty Socket Firmer Chisels
These Henry Taylor chisels have a thicker and longer socket than their bevel edge chisels. This gives them added strength and durability which makes them popular with timber framers.
The handle is made from Ash and has a heavy brass hoop. The handles are hard wearing but should you need to change a handle it is easy to do so with the socketed design. Replacement handles can be made or purchased.
Forged...
Henry Taylor Heavy Duty Socket Firmer Chisels Set of 4
These Henry Taylor chisels have a thicker and longer socket than their bevel edge chisels. This gives them added strength and durability which makes them popular with timber framers.
The handle is made from Ash and has a heavy brass hoop. The handles are hard wearing but should you need to change a handle it is easy to do so with the socketed design. Replacement handles can be made or purchased.
Forged...
Henry Taylor Registered Mortice Chisel
Made in Sheffield, England for over 150 years.
Blade about 5½" long.
F23 - 1/4" (6mm)
F24a - 3/8" (9mm)
F24 - 1/2" (12mm)
F25 - 3/4" (19mm)
F26 - 1" (25mm)
Henry Taylor Registered Mortice Chisel Set of 5
Made in Sheffield, England for over 150 years.
Blade about 5½" long.
F23 - 1/4" (6mm)
F24a - 3/8" (9mm)
F24 - 1/2" (12mm)
F25 - 3/4" (19mm)
F26 - 1" (25mm)
Henry Taylor Swan Neck Chisels
A Henry Taylor swan neck chisel is used to clean the bottom of mortices. The chisel is levered in use, not struck.
Available in 1/4", 5/16" and 3/8".
Hide Mallet Size 10
The head is 89mm (3.5'') in diameter, the length is 140mm (5.5'') and it is made of hide (see below). The total length is approximately 255mm (14'') long and the handle is wooden.
Ideal for the jewellery trade, sheet metal work, die cutting industry and use on copper, brass and soft metals.
This hide mallet has been manufactured from genuine Water Buffalo hide tightly...
Holster for Robert Sorby Timber Framer's Slick
A quality riveted leather holster for safer carriage of the Robert Sorby Timber Framer's Slick.
Lie-Nielsen 10 1/4 Rebate Bench Plane
Also known as a Carriage Maker’s or Jack Rebate Plane, this is the largest rabbet plane made. Based on the Stanley 10¼, which went out of production in the mid-1940s, we modified the design to fit the Bedrock format. Adjustable side nickers make clean, cross-grain cuts. Both handle and knob can tilt left or right to give better access and control in tight corners.
12-3/4" long.
Blade...
Lie-Nielsen No.073 Large Shoulder Plane
A versatile, general purpose Shoulder Plane with nice heft and the best size to start with. This all-metal Shoulder Plane is based on the Record 073, which in turn was based on a Preston model.
The Bronze lever cap is higher for better grip and closer to the blade bevel for better support. The mouth geometry allows for better chip clearance, while the adjustable mouth and locking screws are large...
Lie-Nielsen No.507 Rebating Block Plane
The Lie-Nielsen No 507 Rebating Block Plane is also described as a Lie-Nielsen 60½ Rebating Block Plane (60 1/2R).
This 12° angle rebate block plane is based on an old Sargent block plane (No 507). The plane body is made from unbreakable ductile iron and is ground flat and square to .001". The cap iron is polished bronze. The throat is non adjustable. It is 6¼" long...
Liquid Ink 200ml - Black
For Sumitsubo and Sumisashi, it is water soluble.
Liquid Ink 200ml - Red
For Sumitsubo and Sumisashi, it is water soluble.
Nakaya Ryoba Gold Saw
A double edged blade with X-cut & rip edges and traditional style handle.
A choice of 4 sizes
220mm blade - 0.4mm thick (spacing of teeth 1.3mm cross 2.0-3.4mm rip cut setting 0.7mm) WRG220
240mm blade - 0.5mm thick (spacing of teeth 1.6mm cross 2.7-3.9mm rip cut setting 0.75mm) WRG240 - This is our most popular size.
270mm blade - 0.6 mm thick (spacing of teeth 2.5mm crosscut, 3.3-5.8mm...
Narex Mortice Chisels - Set of 4
Robust mortice chisels for chopping out joints and cutting mortices. Sides taper in height and length from tip to shoulder for sidewall clearance. Bulky handle made from hornbeam which is strong enough to withstand heavy blows with a mallet.
Overall length 304mm.
Available as a boxed set of 4 (4mm, 6mm, 10mm and 12mm).
Oak-Framed Buildings
By Rupert Newman,
The author originally trained as a naval architect and shipwright moved on to oak timber framed construction for houses.
Full colour photographs show projects both complete and under construction. Indented for aspiring self-builders as well as established carpenters and builders. Structural details and three-dimensional drawings are included.
Chapters comprise:
Past...
Replacement Hide Face Size 2
This replacement hide face fits the Copper/Hide Hammer - Branded Head Size 2
Compressed Water Buffalo Hide for use with Malleable Iron heads.
Hide face absorbs the shock of the blow and transfers the force to the item being struck without fear of damage.
Ideal where a heavy blow is required combined with a relatively small striking area.
Robert Sorby Bevel Edged Framing Chisel
Very similar to the RS285 framing chisel that the blade is beveled to give extra clearance in the cut. Tapered along the length. Ash handle. Shorter than the RS285 - 388mm overall length.
Robert Sorby Corner Chisel
Designed for squaring up the ends of mortises, grooves or housings. The faces are precision ground to produce clean, accurate 90 degree angles. Often used nowadays to clean up after a router. Sharpen each face individually with an oil stone.
The origins of this tool are from wheelwrights and millwrights who used a v shaped chisel to hollow out mortises in wheels and wooden beams (often referred...
Robert Sorby Double Hooped Registered Chisel
Originally it was thought that registered (or shipwrights chisels) were used by barge builders and they first appeared in the mid 19th century. “strong ship” or registered chisels were also described in the Scottish tool manufacturer Mathieson’s catalogue of 1900. More recently these chisels have become very popular with joiners and timber framers for mortising. The double hoops give...
Robert Sorby Framing Chisel
The Robert Sorby Framing Chisel is the same principle as their registered chisel but with a longer blade and handle for deeper morticing work.
Overall Size:- 495mm
Blade Length:- 267mm
Robert Sorby Heavy Duty Corner Chisel
A heavyweight 1" (25mm) wide bruzz (corner chisel) for cleaning up deep corners of mortises.
Ash Handle
Overall Size:- 380-407mm
Blade Length 239mm
Robert Sorby Leather Edge Guards
We highly recommend edge guards to protect yourself and your tools.
The chisel guards are available in 1", 1½" and 2" sizes, these tough leather guards are a snug fit for both the 285 and 286 framing chisels.
The slick guards are available in 60mm and 85mm sizes suitable for the 289 framer's slicks.
Robert Sorby Timber Framer's Slick
This heavy duty timber framers and boat builders slick from Robert Sorby has an offset blade to allow for clearance when working in deep sockets and mortises. It can also be used as a massive paring chisel. Choice of two widths - 2-3/8" (60mm) & 3-3/8" (85mm).
Solid one piece forged blade including the heavy tang which is set deep into the handle. A heavy duty socket is fitted between...
Shinwa Ink Line (Sumitsubo)
With a sealed ink reservoir to prevent ink from leaking out or drying up. Automatic spring-loaded recoil with locking mechanism. Unbreakable plastic body and thread bob.
No ink is included.
Body length 180 mm, thread length 20 m.
New design (shiny new colours!)