Sort By
Per Page
View
Grid
List
Pfeil Straight Gouge - Series 9
Straight Gouges are used for shaping recesses and raised surfaces, for instance folds such as drapery. The broad range of sweeps and widths offered by Pfeil opens unlimited possibilities in sculpture carving.
The 15mm is one of our best selling Pfeil tools.
Ray Iles 6' Gent's Drawknife
This Gent's drawknife made by Ray Iles is a delicate drawknife which has a 6" cutting edge and slightly splayed handles. It is made from O1 high carbon tool steel and is fitted with beautiful curved boxwood handles and brass ferrules.
Made in England
Ray Iles 6' Small Draw Knife
The Ray Iles 6" drawknife is a standard carpenter's drawknife, made from 01 high carbon steel and fitted with beech handles and brass ferrules.
Made in England
Ray Iles 8'' Mike Abbott Pattern Draw Knife
This drawknife designed by Mike Abbott and manufactured by Ray Iles has a 8" cutting edge, with beech handles. This 8" drawing knife has slightly flared handles which are bent backwards, meaning the handles are at approximately the same angle, whether you are using them back down, or cannel down.
Made in England
Relief Carving in Wood: A Practical Introduction
By Chris Pye
This is a unique book for woodcarvers. Master woodcarver Chris Pye digs deeply into the process of relief carving by pulling apart a single subject, clearly demonstrating how low and high relief carvings 'work' and how to go about carving them.
Follow this book step by step and you'll learn about the tools and how to handle them properly, and fundamental, transferable carving skills...
Robert Sorby Buffing Mop
Buffing Mop to fit the ProEdge Sharpening Machine.
Also part of the Buffing Kit (PEBUFFKIT)
Robert Sorby Cutter Holder
The Robert Sorby Cutter Holder is a handy little accessory which will accept most of the Robert Sorby cutters.
It avoids skinning fingers when sharpening.
Tip not included.
Robert Sorby Drawknife
10" cutting edge, ash handled draw knife. Straight back and straight blade with slightly splayed handles.
Robert Sorby Fingernail Profiling Kit
The fingernail profiling kit is ideal for shaping those perfect fingernail sweeps on bowl and spindle gouges.
This set contains the arm and the boss but both items are available individually.
Robert Sorby Honing Paste
Applied to a buffing mop the honing paste creates a highly polished finish on any steel.
Robert Sorby Honing Wheel
Honing wheel to fit the ProEdge Sharpening Machine.
Also part of the Honing Kit (WPEPHONEKIT)
Robert Sorby Honing Wheel Arbor
Honing wheel arbor to fit the ProEdge Sharpening Machine.
Also part of the Honing Kit (WPEPHONEKIT)
Robert Sorby Honing Wheel Kit
This kit uses the abrasive honing wheel which can be shaped to allow for honing of gouge flutes - especially useful for woodcarving tools.
Items also available individually.
Robert Sorby Pigtail Mandrel
The Pigtail Mandrel to fit the ProEdge Sharpening Machine.
Also part of the Buffing Kit (PEBUFFKIT)
Robert Sorby ProEdge Aluminium Oxide Belts
This common abrasive is designed primarily to sharpen carbon steel bench chisels, carving tools and plane irons but will also hone harder high speed steel tools.
The material longevity is at the lower end of the abrasives scale they use on their belts, but makes an excellent economical choice. Work your way through grit sizes (heavier grits for the removal of more material) to achieve a fine finish...
Robert Sorby ProEdge Buffing Kit
The Robert Sorby ProEdge Buffing Kit includes:
Robert Sorby ProEdge Pigtail Mandrel
Robert Sorby ProEdge Buffing Wheel
Robert Sorby ProEdge Ultra-Fine Buffing Compound
Robert Sorby ProEdge Ceramic Belts
This hardwearing material is a great choice for profiling and re-profiling damaged tools.
The heavier 60 grit option is an efficient choice for removing plenty of material, while the finer 120 grit will provide a satisfying finish. Great longevity and highly practical.
Robert Sorby ProEdge Knife Holder Large
For hunting knives and those with blades over 8".
Please note that you will already need to own a jig to use this (either the PEKJIGS or PEKJIGL).
Robert Sorby ProEdge Knife Holder Small
The Robert Sorby ProEdge Small Knife Holder can be used for pocket knives, carving knives and blades up to 8" long.
Please note that you will already need to own a jig to use this (either the PEKJIGS or PEKJIGL).
Robert Sorby ProEdge Long Grind Jig
Helps you to create three different fingernail profiles.
Robert Sorby ProEdge Proset
Achieving the exact bevel angle on any fingernail or long grind gouge has never been easier than with the Robert Sorby Proset.
By placing the gouge into the clamp of the profile arm and then extending the gouge up-to the required stop and locking it into place will allow for precise and repeatable bevel angles to be obtained.
Robert Sorby ProEdge Skew Jig
The Skew Jig allows the turner to accurately and safely sharpen his skew chisels.
Robert Sorby ProEdge Trizact Belts
Perhaps the most popular in the range of belts. This robust material is designed to handle the demands of all steels. Not strictly 'grit sizes' these belts are built using brick and pyramid abrasive shaping.
The highest 3000 'grit' size will sharpen to two microns (the same sharpness as a disposable razor blade) and provide a factory finish on all steels.
Robert Sorby ProEdge Zirconium Belts
Designed for HSS tools, drill and router bits this material provides good value.
The 60 grit belt will tackle the most damaged surface. Use the 120 grit to provide a rewarding cutting edge and finish.
Robert Sorby Short Tool Platform with Arm
Increases access when tools are getting old and worn.
Robert Sorby Standard Gouge Jig
Allows easy sharpening of all standard ground woodworking gouges.
Robert Sorby Woodworkers' Square Guide
This simple to use jig has been designed as an upgrade to the current woodworking chisel jig (PESQ). This jig can be adjusted to ensure exact and repeatable 90 degree angles can be achieved every time. A stepped plate raises the tool to be sharpened away from the tool platform.
Ideal for sharpening chisels and plane irons.
Robert Sorby Woodworking Chisel Jig
Accurately ensures a straight cutting edge on any woodworking chisel.
Robin Wood Large Carving Axe
A large head with a long cutting edge, a flat grind for carving and a curvy ergonomic handle. A textured handle gives it beautiful grip in use. This heavier version of the Wood Tools carving axe is ideal for larger work like bowl carving, or for the stronger carver who is looking for something with a bit more power.
The natural wood materials and hand grinding means there will be some aesthetic...
Saburrtooth 1/4'' Ball Nose - 1/2'' x 3/4''
Head Diameter: 1/2''
Head Length: 3/4''
Saburrtooth 1/4'' Ball Nose - 1/4'' x 1 3/4''
Head Diameter: 1/4"
Head Length: 1¾"
Saburrtooth 1/4'' Ball Nose 3/4'' x 1 1/4''
Head Diameter: 3/4"
Head Length: 1¼"
If grits are not displayed they are no longer available.
Saburrtooth 1/4'' Burrs Set - Coarse
This set of burrs from Saburrtooth includes:
14BN14 - Ballnose, head diameter 1/4" and head length 1 3/4"
14F12 - Flame, head diameter 1/2" and head length 3/4"
14S58 - Sphere, 5/8" diameter
14C12 - Cylinder, head diameter 1/2" and head length 3/4"
14T14 - Taper, head diameter 1/4" and head length 1 3/8"
14RS34 - Rotosaw, head diameter 3/4"...
Saburrtooth 1/4'' Burrs Set - Fine
This set of burrs from Saburrtooth includes:
14BN14 - Ballnose, head diameter 1/4" and head length 1 3/4"
14F12 - Flame, head diameter 1/2" and head length 3/4"
14S58 - Sphere, 5/8" diameter
14C12 - Cylinder, head diameter 1/2" and head length 3/4"
14T14 - Taper, head diameter 1/4" and head length 1 3/8"
14RS34 - Rotosaw, head diameter 3/4"...
Saburrtooth 1/4'' Concave - 1/2'' x 3/4''
Head Diameter: 1/2''
Head Length: 3/4''
Saburrtooth 1/4'' Concave - 1/2'' x 3/4'' (Smooth End)
Head Diameter: 1/2"
Head Length: 3/4"
Saburrtooth 1/4'' Cross Cutter - 1/2''
Shape: Cross Cut Eyecutter
Diameter: 1/2''
Head Length: 1/2
Saburrtooth 1/4'' Cross Cutter - 3/4''
Shape: Cross Cut Eyecutter
Diameter: 3/4''
Head Length: 3/4
Saburrtooth 1/4'' Cross Cutter 1''
Shape: Cross Cut Eyecutter
Diameter: 1''
Head Length: 1"
Saburrtooth 1/4'' Cylinder - 1'' x 1''
Head Diameter: 1''
Head Length: 1''
Saburrtooth 1/4'' Cylinder - 1'' x 1'' - (Radius End)
Head Diameter: 1"
Head Length: 1"
Saburrtooth 1/4'' Cylinder - 1'' x 1'' - (Smooth End)
Head Diameter: 1"
Head Length: 1"
Saburrtooth 1/4'' Cylinder - 1/2'' x 3/4''
Head Diameter: 1/2"
Head Length: 3/4"
Saburrtooth 1/4'' Cylinder - 1/2'' x 3/4'' - (Smooth End)
Head Diameter: 1/2"
Head Length: 3/4"
Saburrtooth 1/4'' Cylinder - 1/4'' x 1 3/4''
Head Diameter: 1/4"
Head Length: 1¾"
Saburrtooth 1/4'' Cylinder - 1/4'' x 1 3/4'' - (Smooth End)
Head Diameter: 1/4"
Head Length: 1¾"
Saburrtooth 1/4'' Cylinder - 3/8'' x 3/4''
Head Diameter: 3/8"
Head Length: 3/4"
Saburrtooth 1/4'' Cylinder 3/4'' x 1 1/4''
Head Diameter: 3/4"
Head Length: 1¼"
If grits are not displayed they are no longer available.