Sort By
Per Page
View
Grid
List
Robert Sorby ProEdge Aluminium Oxide Belts
This common abrasive is designed primarily to sharpen carbon steel bench chisels, carving tools and plane irons but will also hone harder high speed steel tools.
The material longevity is at the lower end of the abrasives scale they use on their belts, but makes an excellent economical choice. Work your way through grit sizes (heavier grits for the removal of more material) to achieve a fine finish...
Robert Sorby ProEdge Buffing Kit
The Robert Sorby ProEdge Buffing Kit includes:
Robert Sorby ProEdge Pigtail Mandrel
Robert Sorby ProEdge Buffing Wheel
Robert Sorby ProEdge Ultra-Fine Buffing Compound
Robert Sorby ProEdge Ceramic Belts
This hardwearing material is a great choice for profiling and re-profiling damaged tools.
The heavier 60 grit option is an efficient choice for removing plenty of material, while the finer 120 grit will provide a satisfying finish. Great longevity and highly practical.
Robert Sorby ProEdge Knife Holder Large
For hunting knives and those with blades over 8".
Please note that you will already need to own a jig to use this (either the PEKJIGS or PEKJIGL).
Robert Sorby ProEdge Knife Holder Small
The Robert Sorby ProEdge Small Knife Holder can be used for pocket knives, carving knives and blades up to 8" long.
Please note that you will already need to own a jig to use this (either the PEKJIGS or PEKJIGL).
Robert Sorby ProEdge Long Grind Jig
Helps you to create three different fingernail profiles.
Robert Sorby ProEdge Proset
Achieving the exact bevel angle on any fingernail or long grind gouge has never been easier than with the Robert Sorby Proset.
By placing the gouge into the clamp of the profile arm and then extending the gouge up-to the required stop and locking it into place will allow for precise and repeatable bevel angles to be obtained.
Robert Sorby ProEdge Skew Jig
The Skew Jig allows the turner to accurately and safely sharpen his skew chisels.
Robert Sorby ProEdge Trizact Belts
Perhaps the most popular in the range of belts. This robust material is designed to handle the demands of all steels. Not strictly 'grit sizes' these belts are built using brick and pyramid abrasive shaping.
The highest 3000 'grit' size will sharpen to two microns (the same sharpness as a disposable razor blade) and provide a factory finish on all steels.
Robert Sorby ProEdge Zirconium Belts
Designed for HSS tools, drill and router bits this material provides good value.
The 60 grit belt will tackle the most damaged surface. Use the 120 grit to provide a rewarding cutting edge and finish.
Robert Sorby Recess Bead Cove Cutter Set
This set of three cutters for Robert Sorby's Multi-tip Hollowing Tool.
The RS236C is the larger of two double sided beading cutters and is designed to cut 3/8'' and 5/8'' beads. Designed for use with: Multi-tip Hollowing Tool (RS200KT and RS200).
Similarly the RS235C is the larger of two cove cutters. This cutter is perfectly designed to cut coving on spindle work to 3/8''...
Robert Sorby Recessing & Dovetailing Cutter
The Recess and Dovetail cutter (RS-234C) is the perfect tool for creating dovetails and recesses at 45 – 60º – ideal for creating a foot on a bowl.
Designed for use with: Multi-tip Hollowing Tool (RS-200KT and RS-200) and Swivel Tip Probe (RS-8803H)
High Speed Steel.
Robert Sorby Relief Cutting Tool
The Robert Sorby Relief Cutting Tool enables the turner to produce a recess prior to threading.
Robert Sorby Round End Swivel Tip
The Robert Sorby Round End Swivel Tip is an excellent choice for removing waste material very quickly especially undercutting. A true work horse designed for the multi-tip hollowing tool but suitable for a range of Robert Sorby tools (see below)
Sharpening: Use a diamond file or honing stone flat across the face. To gain best results and increase the longevity of the cutter this simple procedure...
Robert Sorby Round Nose Scraper
The Robert Sorby Round Nose Scraper is used on bowls and spindle work to create smooth flowing curves e.g goblets, egg cups, and inside boxes.
Robert Sorby Round/Side Cut Scraper
The Robert Sorby round/side cut scraper is designed for blending the parallel side wall and the curved bottom of vessels together. It is excellent for undercutting the rims of small bowls.
3/4" Round Side Cut Scraper - 16" with handle
Robert Sorby RSJ1 Jaws - 1' (25mm)
1" Jaws. With a fine internal and external dovetail, these 1" jaws are perfect for gripping miniature projects. The jaws expand from 25mm to 50mm and compress from 39mm down to 14mm.
Also compatible with Nova and Supernova chucks.
The photo shows the RSJ1 Jaws fitted to a Patriot Chuck (not included).
Robert Sorby RSJ15 Jaws 1 3/8' (35mm)
1 3/8" Jaws. Designed for smaller projects like boxes and bowls up to 6".
The photo shows the RSJ15 Jaws fitted to a Patriot Chuck (not included).
Robert Sorby RSJ3 Jaws 2 3/4' (70mm)
2 3/4" Jaws. For larger projects and bowls up to 13" where a little extra grip is required.
The photo shows the RSJ3 Jaws fitted to a Patriot Chuck (not included).
Robert Sorby RSJ4 Jaws 3 1/2' (89mm)
3 1/2" Jaws. Intended for bowls up to 16" needing substantial holding power.
The photo shows the RSJ4 Jaws fitted to a Patriot Chuck (not included).
Robert Sorby RSJ5 Jaws 4 1/4'' (108mm)
Robert Sorby RSJ5 4¼" Jaws these jaws enable a much bigger recess or spigot to be held and are hence designed for bowls and platters over 16".
The photo shows the RSJ5 Jaws fitted to a Patriot Chuck (not included).
Robert Sorby RSJDG Deep Grip Jaws
Robert Sorby Deep Grip Jaws have deep sides of these jaws make them ideal for large logs or awkward pieces of wood. They come with both internal and external dovetails to hold cumbersome pieces securely.
The photo shows the RSJDG Jaws fitted to a Patriot Chuck (not included).
Robert Sorby Sandmaster
The Robert Sorby Sandmaster is an essential part of every turner's tool kit.
It comes with 5 different grits of abrasive to take even the roughest projects to a glass-like finish every time. It has an adjustable 2" velcro pad and comes complete with 2 each of 60, 120, 180, 240 & 400 grit sanding discs. You avoid the uneven finish often associated with hand sanding and there is no danger...
Robert Sorby Sandmaster 2'' Sanding Discs
Robert Sorby Sandmaster 2" velcro sanding discs.
Aluminium Oxide. Supplied in packs of 10
Robert Sorby Short Tool Platform with Arm
Increases access when tools are getting old and worn.
Robert Sorby Side & End Swivel Tip
The Robert Sorby Side End Swivel Tip is designed to create parallel sides on boxes and vases. This flexible cutter will also create flat surfaces on the bottom of pieces as well as crisp corners.
Sharpening: Use a diamond file or honing stone flat across the top face. To gain best results and increase the longevity of the cutter this simple procedure should be done little and often.
Related Products:...
Robert Sorby Sizing Tool
The Robert Sorby Sizing Tool is used in conjuction with a parting tool to obtain accurate and consistent diameters up to 3" on spindlework. It fits either the Robert Sorby 3/8" beading and parting tool or bedan.
The two thumb screws lock the sizing tool firmly in place.
How to use:
Set the parting tool to the desired size with a steel rule – lock tool in position by tightening...
Robert Sorby Small Tear-drop Scraper
The Robert Sorby small tear drop cutter provides a multi-facetted, highly efficient cutting edge. The shape of the cutter effectively converts the tool into a round, half-round or square scraper suitable for use on the inside or outside of small bowls, platters and hollow forms. Use the straight edge on outside curves and the rounded shapes for internal curved shapes. A great all rounder that supports...
Robert Sorby Spindle Roughing Gouges
Robert Sorby spindle roughing gouges are for initial turning of uneven or square stock to round. The shape of the roughing out gouge enables the tool to cut safely with the wings (the name given to the tips of the side walls) well back from the workpiece.
Robert Sorby Spindlemaster - 812H
The spindlemaster will create beads & coves as well as planing and trimming end grain.
Taming the skew is perhaps the most common of problems encountered by the woodturner. The digs-ins which ensue from incorrect presentation cause many turners to avoid using the skew chisels and consequently reduce their skills and limit their opportunities of turning between centres. The new Spindlemaster...
Robert Sorby Spiralling System
The Robert Sorby Spiralling System is a further development of the texturing tool and is used to create both left and right handed spirals with ease. Creating barley twists, spirals and flutes has always represented a problem for the woodturner, the Spiralling System not only overcomes many of these difficulties, but also allows the turner’s imagination to run wild as he enters a new field of...
Robert Sorby Standard Bowl Gouges (Deep Flute)
The Robert Sorby standard bowl gouges are a must in the tool kit of every bowl turner.
These tools are ideal for making bowls, capable of producing either massive profiling cuts or delicate finishing cuts as necessary.
Robert Sorby Standard Gouge Jig
Allows easy sharpening of all standard ground woodworking gouges.
Robert Sorby Standard Parting Tools
Robert Sorby standard parting tools are used to part the finished project off from the waste material, the parallel sides make for a rigid tool that handles well. The 1/8" (3mm) tool reduces the amount of waste, vital if the timber is an expensive, exotic one.
It also makes for a fine detailing tool, e.g. beads and fillets.
Robert Sorby Standard Skew Chisels
Robert Sorby standard skew chisels are rectangular in section, giving this type of of skew more weight. This makes them superb for large spindle work e.g kitchen table legs and newel posts.
Robert Sorby Standard Spindle Gouges
The Robert Sorby Standard Spindle Gouges are ideal tools for detailed work between centres, such as creating coves, beads, and other profiles on spindle projects. Available in sizes ranging from 1/4'' to 3/4'', these gouges feature comfortable handles and are suitable for turning projects like goblets, vases, and egg cups.
Robert Sorby SteadyPro Turning System
The Robert Sorby SteadyPro is a very easy to use jig that provides additional tool support when hollowing as well as many other woodturning operations.
The versatile SteadyPro fits a wide range of woodturning lathes by utilising the stems from the Robert Sorby modular tool rest system.
With the easy to adjust cantilever action of the clamping rollers, this ensures the optimum control for a large...
Robert Sorby SteadyPro Turning System - With Stem
The Robert Sorby SteadyPro is a very easy to use jig that provides additional tool support when hollowing as well as many other woodturning operations.
The versatile SteadyPro fits a wide range of woodturning lathes by utilising the stems from the Robert Sorby modular tool rest system.
With the easy to adjust cantilever action of the clamping rollers, this ensures the optimum control for a large...
Robert Sorby Steb Drive
The Robert Sorby Steb Drive is a highly effective woodturning accessory designed for use with a lathe. It fits into the jaws of a Patriot chuck and uses serrated teeth combined with a spring-loaded centre pin for a secure grip on wood, preventing slippage during turning. Available in multiple sizes (7/8", 1/2", and 1 1/4"), this tool is perfect for woodturning projects that require precision...
Robert Sorby Texturing Tool
This Robert Sorby Texturing Tool is a remarkable adaptation of an engineer's knurling tool. It consists of a handle, blade and a double bevelled texturing cutter with integral bearing.
It can be used to create unique effects that alter the tactile and visual qualities of your bowls, hollow forms, goblets or boxes perfect for adding that individual mark to your work. Orange peel, striated and...
Robert Sorby Thread and Sizing Gauge
The Robert Sorby thread and sizing gauge takes the guesswork out of dimensioning.
Robert Sorby Thread Cutters (pair of)
These Robert Sorby thread cutters were designed in conjunction with master turner Robert Sorby and have been specially produced for cutting in wood.
Thread cutters are available in matching pairs for internal and external threads.
The Relief Tool is a handy accessory to cut the relief in the bottom of female threads whilst the Tool Support enables extra access.
The gauge is extremely useful...
Robert Sorby Thread Cutting Sets - 89HS
The Robert Sorby Thread Cutting Sets comprise a choice of 10, 16 or 20 tpi thread cutter pairs made in high speed steel with a unique helix angle for use in wood, a thread & sizing gauge and an instructional DVD "Focus on Threadcutting"
We also stock the Relief Cutting Tool (RS-895H), Tool Support (RS-893H) and the Thread and Sizing Gauge (RS-973) - all of these will make the forming...
Robert Sorby Tool Rest Adjustment Collar
The Robert Sorby Tool Rest Adjustment Collar allows easy height adjustments of your tool rest by up to 1/2" (13mm) without losing the set height when the locking handle is released. It features an outer adjustment ring for precise control and an Acetal seating disc for smooth operation. Available in stem sizes of 3/4", 1", 25mm, and 30mm, it's perfect for woodturners seeking flexibility...
Robert Sorby Tool Rest Crossbar 4'
Most turners have problems with their lathe tool rest. The majority are either cast or made from low grade and tend to be relatively soft. As a result , when a square tool, like a parting tool, is used it can dig into the rest creating a series of notches. This in turn makes it very difficult to produce a smooth flow along the rest when trying to take an even cut.
The cross bars from the new Modular...
Robert Sorby Tool Rest Crossbar 6'
Most turners have problems with their lathe tool rest. The majority are either cast or made from low grade and tend to be relatively soft. As a result , when a square tool, like a parting tool, is used it can dig into the rest creating a series of notches. This in turn makes it very difficult to produce a smooth flow along the rest when trying to take an even cut.
The cross bars from the new Modular...
Robert Sorby Tool Rest Crossbar 9'
Most turners have problems with their lathe tool rest. The majority are either cast or made from low grade and tend to be relatively soft. As a result , when a square tool, like a parting tool, is used it can dig into the rest creating a series of notches. This in turn makes it very difficult to produce a smooth flow along the rest when trying to take an even cut.
The cross bars from the new Modular...
Robert Sorby Tool Rest for Thread Cutting
The Robert Sorby Tool Rest for thread cutting provides extra control when creating internal threads.