Sort By
Per Page
View
Grid
List
New Veritas Micro-Adjust Wheel Marking Gauge
Veritas have refined and redesigned their ever popular wheel marking gauges. This new micro-adjust wheel marking gauge draws on two decades of manufacturing experience, with subtle improvements across the board.
The adjustment mechanism built into the stainless-steel rod is intuitive to use. After setting the approximate projection, you can fine-tune the position of the cutter within a range of...
Veritas Micro Adjust Marking Gauge
The Veritas wheel marking gauge is a great workhorse and excellent value. Its popularity led to the development of a second model that incorporates a micro-adjust feature. It is similar to our standard wheel marking gauge with an anodized aluminium body, brass face, stainless-steel rod and internal O-ring to keep a constant light friction force on the rod. It differs in that the body is slightly...
Veritas Dual Marking Gauge
The Veritas Dual Marking Gauge has two independently adjustable rods, which will allow you to set two measurements at once, so you can quickly alternate between them when transferring or marking repetitive dimensions. Projection up to 5-3/4" is easy to set, since an internal O-ring keeps light but constant friction on each rod; a thumbscrew firmly locks rods in place.
Like other Veritas marking...
Veritas Standard Marking Gauge
Standard Gauge - pretty much the same construction as the micro adjust but these are slighly shorter at 6" and do not have the micro adjust feature.
Tite-Mark Standard
The Tite-Mark Range is manufactured by Glen Drake Toolworks and distributed by Lie-Nielsen.
The unique micrometer adjustment makes these marking gauges an easy and very accurate tool to use. It has steel shafts with brass body and fixed circular A2 blade hardened to 58-60 Rockwell. The blade retracts safely into a recess in the head.
The Tite-Mark Standard (7" long shaft) is built around a 5/16"...
Tite-Mark Long
The Tite-Mark Range is manufactured by Glen Drake Toolworks and distributed by Lie-Nielsen.
The unique micrometer adjustment makes these marking gauges an easy and very accurate tool to use. It has steel shafts with brass body and fixed circular A2 blade hardened to 58-60 Rockwell. The blade retracts safely into a recess in the head.
Joseph Marples Trial 1 - Combined Marking & Mortice Gauge
The Joseph Marples Trial 1 Screwslide Marking and Mortice Gauge has a full 1/8" thick brass face.
The stock is locked on to the stem by brass knurled thumbscrew and protective pressure pad. The locking screw is set within a traditional brass protective shield.
A screw slide gives fine and precise adjustment of the mortice pins and on the back of the stem is a single marking gauge pin.
Lee Valley 3-in-1 Brass Marking Gauge
This elegant Lee Valley marking gauge is really three tools in one - a wheel gauge, a pin gauge, and a cutting gauge.
The unique swivelling pin/blade chuck takes either a pin or a blade that locks in place (after extension is set) using a set screw in the end of the 4½" gauge stem. The cutting blade can be set for either right or left handed use. The opposite end of the stem is tapped to accept...
Veritas Carpenter's Gauge
Specifically designed to be carried in an apron or pocket, this is both a direct-reading compass and a marking gauge, two things that carpenters frequently need but find hard to carry.
It has a rotatable head, which locks vertically for use and horizontally for storage and tip protection. It is direct reading, both for radius and diameter, in inches and centimetres. If you have ever measured a...
Veritas Miniature Marking Gauges
These are fully working versions of the Veritas wheel marking and dual marking gauges, but only one third of the size. Their smaller scale allows greater control and makes these exquisite tools perfect for small marking tasks that require a delicate touch. Each is 57mm long and weighs just over 14g and 21g respectively.
Like their full-size counterparts, they cut (not tear) fibres for clear marks...
Replacement Blade for Tite-Mark Marking Gauge
Replacement Blade for Tite-Mark Standard and Long Marking Gauges.
Tite-Mark - Mortice Blades (pair)
Pair of Mortice Blades for laying out mortices for Tite-Mark Standard and Long Marking Gauges
Tite-Mark Extensions
A pair of extension rods to fit the Tite-Mark Standard. One 3" (7.62cm) and one 6" (15.24cm) extension rod may be used individually or joined together to extend the reach of the Titemark an extra 9" (22.86cm) by being screwed onto the blade end.
Tite-Mark Fixed Width Mortice Blade Set
Tite-Mark fixed width mortice blades - set of 4 with hex key.
1/2", 3/8", 5/16" and 1/4" for Tite-Mark Standard and Long Marking Gauges
Tite-Mark Scoring Blade
Tite-Mark scoring blade for deep marking, slicing veneer strips and other general scoring tasks for the Tite-Mark Standard and Long Marking Gauges
Veritas Marking Gauge Replacement Wheel
Replacement wheel for Veritas gauges. Not suitable for the new style micro-adjust marking gauge.
Veritas Marking Gauge Replacement Wheel - (Inside)
Replacement wheel for the Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
Veritas Marking Gauge Replacement Wheel - (Outside)
Replacement wheel for the new style Micro-adust and Dual Marking gauges. Both the Inside and Outside cutters are required for the Dual Marking gauge.
Veritas Marking/Mortice Gauge Heads
Though designed for use with their Veritas® Wheel Marking Gauges, these gauge heads are a simple retrofit for any marking gauge with a 5/16" diameter shaft.
Made from carbon steel, the 5/8" diameter wheel cutters will scribe at any point in their circumference and slice rather than tear fibers for clean, accurate cuts. The single-bevel cutters are usable in-line for marking parallel lines, or...
Veritas Micro-Adjust Rod for Wheel Marking Gauges
We offer the micro-adjust rod separately from the gauge body to let you easily upgrade a Veritas standard wheel marking gauge you own with the new adjustment mechanism.
Veritas Shaft Clamp for Dual Marking Gauge
On occasions, it may an advantage to lock the relative position of the two rods on the Veritas® Dual Marking Gauge, such as when a project requires a constant mortise size, but different offsets. The shaft clamp lets you lock the relative position of the cutters while still being able to adjust the fence for offset. This allows you to preserve identical mortise or tenon sizing when joining parts...