Sort By
Per Page
View
Grid
List
Blue Spruce Optima Mortise Chisels - Curly Maple
Blue Spruce Toolworks new Optima Chisels feature a lapped and polished back with a flatness measured in light bands (the same system used to measure silicon wafers). When you unbox your new Optima Chisels, they’re razor sharp and 100% ready to go to work.
Each Optima Chisel is machined from A2 tool steel, then double-tempered and cryogenically treated. The tempering and cryo treatments result...
Narex Richter Mortice Chisels
These are the premium range of mortice chisels from Narex which have earnt the name ''Richter'', who was the founder of Narex company in the Czech Republic.
Sides are slightly relieved to reduce sidewall friction and to allow minor adjustments.
CR-V cryogenically treated steel to 62HRc .
Ash handles with a stainless steel hoop and ferrule.
149mm blade length. 284mm overall...
Narex Richter Mortice Chisels Set
These are the premium range of mortice chisels from Narex which have earnt the name ''Richter'', who was the founder of Narex company in the Czech Republic. Includes the 1/8'' (3.2mm), 1/4'' (6.3mm), 3/8'' (9.5mm) and 1/2'' (12.7mm).
Sides are slightly relieved to reduce sidewall friction and to allow minor adjustments.
CR-V cryogenically treated...
Narex Mortice Chisels - Set of 4
Robust mortice chisels for chopping out joints and cutting mortices. Sides taper in height and length from tip to shoulder for sidewall clearance. Bulky handle made from hornbeam which is strong enough to withstand heavy blows with a mallet.
Overall length 304mm.
Available as a boxed set of 4 (3mm, 6mm, 10mm and 12mm).
Robert Sorby Sash Mortice Chisel
Used for light mortising work, satinwood handle. A 2 degree taper prevents binding in the cut. Ideal for clearing out waste from mortices for tenons, locks and hinges. Can be used with a mallet.
Overall Size:- 279mm
Blade Length 159mm
.png "Last Ones!")
Veritas PM-V11 Mortice Chisels
These are substantial mortice chisels. The blades are more than 1/2" thick at the heel of the bevel and are a consistent width from tip to shoulder for accurate registration in a mortice.
The chisel sides are slightly relieved to reduce sidewall friction and allow for minor cut corrections. Each has a 25° primary bevel to make deep cuts easier, with a 35° secondary bevel to give them...
Lie-Nielsen Mortice Chisels
SPECIAL NOTE - MARCH 2025
Please have a look at our Friday Finds section as we currently currently have 2 pre-owned (but hardly used) sets that will save you a few well earned pounds!
Designed with cabinetmaking in mind, these well-balanced Mortise Chisels are ground with parallel sides and are thicker than they are wide to help keep them straight in the cut.
Made of A2 Tool Steel, hardened...
Henry Taylor Registered Mortice Chisel
Made in Sheffield, England for over 150 years.
Blade about 5½" long.
F23 - 1/4" (6mm)
F24a - 3/8" (9mm)
F24 - 1/2" (12mm)
F25 - 3/4" (19mm)
F26 - 1" (25mm)
Henry Taylor Registered Mortice Chisel Set of 5
Made in Sheffield, England for over 150 years.
Blade about 5½" long.
F23 - 1/4" (6mm)
F24a - 3/8" (9mm)
F24 - 1/2" (12mm)
F25 - 3/4" (19mm)
F26 - 1" (25mm)
![Veritas - Mark II Deluxe Honing Guide Set [Preowned, SOLD]](/images/products/thumbs/3955_10164.jpg "Veritas - Mark II Deluxe Honing Guide Set [Preowned, SOLD]")
![Veritas - Mark II Deluxe Honing Guide Set [Preowned, SOLD]](/images/products/thumbs/3955_10163.jpg "Veritas - Mark II Deluxe Honing Guide Set [Preowned, SOLD]")
