Sort By
Per Page
View
Grid
List
Flexcut 1'' Mini Draw Knife KN17
This miniature draw knife by Flexcut is designed for hard-to-reach areas, where a pulling action is more conducive to efficient stock removal. The flexible shank allows the cutting angle to be changed easily for contoured cuts.
Made in the USA by Flexcut.
Journeyman Handcrafts Wool Lined Tool Roll
Keep your carving tools protected and portable with this Journeyman Handcrafts tool roll made from a two colours of 8oz waxed cotton canvas giving a lovely contrast of colour when rolled up. The tool roll is lined with a cream wool to give added protection to your tools.
This tool roll is made to last and will endure many years of hard use. It’s double stitched with a very strong bonded nylon...
Oscar Rush Large Bowl Adze
A hand forged 50mm diameter hand adze with elliptical sweep profile to the cutting edge.
The head weight is approximately 600g with a 230mm - 235mm long (just over 9"), hand carved, faceted, kin dried ash handle.
The leather adze cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
This adze has been carefully designed for shaping...
Oscar Rush Large Carving Axe - Double Grind
A large carving axe with a really broad edge (DOUBLE SYMMETRICAL grind), designed to throw big chips!
This axe will still work well in the right hands when creating smaller carvings.
145mm - 150mm (6") edge - SYMMETRICAL grind.
The head weight is approximately 850 - 900g - SO BEWARE THIS IS QUITE A BEAST
NOTE - Should you wish to strike the poll, please do so with a wooden mallet (not...
Oscar Rush Large Carving Axe - Left Grind
A large carving axe with a really broad edge (left grind), designed to throw big chips!
This axe will still work well in the right hands when creating smaller carvings.
145mm - 150mm (6") edge - LEFT grind.
The head weight is approximately 850 - 900g - SO BEWARE THIS IS QUITE A BEAST
NOTE - Should you wish to strike the poll, please do so with a wooden mallet (not a steel hammer).
Handle...
Oscar Rush Large Carving Axe - Right Grind
Large carving axe (RIGHT GRIND) with a really broad edge, designed to throw big chips!
This axe will still work well in the right hands when creating smaller carvings.
145mm - 150mm (6") edge - RIGHT grind.
The head weight is approximately 850 - 900g - SO BEWARE THIS IS QUITE A BEAST
NOTE - Should you wish to strike the poll, please do so with a wooden mallet (not a steel hammer).
Handle...
Oscar Rush Medium Carving Axe
A standard weight carving axe retaining a relatively compact design but with a broader curved edge for slicy cuts.
This carving axe has a 120mm - 125mm (5") edge - SYMMETRICAL grind only for this axe (also known as double grind).
The head weight is approximately 625g. If striking the poll, do so with a wooden mallet (not a steel hammer)
The handle - hand carved 300mm -320mm long (12"...
Oscar Rush Small Bowl Adze
A hand forged 30mm diameter hand adze with a compound sweep profile to the cutting edge (more of a U profile).
The head weight is approximately 450g with a 210mm - 215mm long (just over 8") hand carved, faceted, kin dried ash handle.
The leather adze cover is made by Oscar using Italian leather with solid brass rivets (these are much stronger than cap rivets).
This adze has been carefully...
Oscar Rush Small Carving Axe
A small carving axe for all sizes of carving.
This stout hand forged carving axe has a 95mm - 100mm (4") edge - SYMMETRICAL grind (also known as double grind).
The head weight is approximately 475 - 500g.
If striking the poll, do so with a wooden mallet (not a steel hammer).
Handle - hand carved 275mm - 285mm long (just over 11"), faceted, kin dried ash handle.
The leather...
Gransfors Bruk Large Carving Axe 475
A chop axe for hewing bowls and other wooden objects, artistic wood carving and architectural work. The characteristic curved shape of the cutting edge, carried well above the head’s eye, the position of the edge in proportion to the handle, the rather thick bit and the big angle of the wide beveled face makes the axe a good carving tool. You "cut on the beveled face" with curved movements. This...
Pfeil Hatchet
The Pfeil Hatchet is forged from quality steel.
Overall length 460mm (about 18")
Weight 1300gms with cutting edge of 140mm.
Pfeil Sculptor's Hatchet
The Pfeil Sculptor's Hatchet is a small hatchet which is very handy and easy to guide. With leather edge protector.
Overall length 280mm (about 11")
Weight 550gms with cutting edge of 80mm.
Pfeil Sculpture's Adze
The Pfeil Sculptor's Adzes follow old French designs.
Available with Straight, Curved or Round blades, these tools are forged from quality tool steel, hardened and sharpened with Hickory handles.
Straight:
Overall length 450mm (about 18").
Weight 800gms.
Cutting edge of 65mm.
Curved:
Overall length 450mm (about 18")
Weight 850gms.
Cutting edge of 60mm.
Round:
Overall...
Henry Taylor Bowl Adze
Sheffield made hand forged adzes by Henry Taylor for single handed use.
This one is a tight gouge (sweep 9), however this lucky fella is outcannel which makes it a Bowl Adze.
At the other end to the cutting edge is a square faced hammer poll.
All Henry Taylor adzes have an ash handle of 250mm (about 10") .
The overall head size (from the square face of the hammer poll to the cutting edge)...
Henry Taylor Hand Adze Deep Curved Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use.
There is a choice of 3 adzes; this one is a tight incannel gouge (sweep 9), and is offered with an incannel or outcannel grind.
The outcannel grind is favoured by those working concave surfaces as it allows the leading edge to enter the working area easier.
At the other end to the cutting edge is a square faced hammer...
Henry Taylor Hand Adze Shallow Curved Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use.
There is a choice of 3 adzes, this one a gouge end with a shallow/mid gouge or there is a tight gouge (sweep 9) and a 50mm (2") straight edge (like a chisel).
At the other end to the cutting edge is a square faced hammer poll.
All the adzes have an ash handle of 250mm (about 10") .
The overall head size (from the...
Henry Taylor Hand Adze Straight Blade
Sheffield made hand forged adzes by Henry Taylor for single handed use.
There is a choice of 3 adzes, this one a 50mm (2") straight edge (like a chisel) or curved end (like a gouge) with either a shallow/mid gouge or a tight gouge (sweep 9).
At the other end to the cutting edge is a square faced hammer poll.
All the adzes have an ash handle of 250mm (about 10") .
The overall head size...
Muller French-Style Sculptors Adze
Again, these adzes are from Leonhard Muller's Carpenter's Hatchets range but they are based on the traditional French design where the head gradually flares from the poll. 3 sweep widths to chose from and all come with straight hickory handles.
Straight 450mm hickory handles (about 18")
Choice of 65mm, 60mm or 56mm wide medium sweep cutting edge.
Auriou 'Mellow Hog' Rasp
The Mellow Hog Rasp - Half round 12" (300mm) G6
A Mellow Hog is a calmer version of its aggressive brother The Hog. The difference between the cut of the 2 rasps can be seen in the photos.
The original Hog has the coarsest cut for hand rasps made by Forge de Saint Juery at cut 3 (cut = stitch).
The Hog is a great tool for reducing roughed out blanks for cabriole legs and guitar necks...
Auriou Curved Cabinet Maker's Rasp
Useful for shaping the buttock areas for chair seats and for other concave shaping work. This 10" cabinet rasp is stitched on the underside only and is curved along its length.
Size - 250mm x 32mm x 5.5mm Grain 9
Left Handed Auriou Albi Combination Rasps
These are the Left Handed versions, to see the Right Handed please CLICK HERE.
These are stitched on both sides with one "safe edge".
The rasp is thinner close to its tip to allow ease of entry into your workpiece. For flat and convex work only.
As normal, the longer the rasp, the coarser it is. We offer 2 sizes. The sizes shown are the rasp dimensions without the handle.
The...
Left Handed Auriou Cabinet Maker's Rasps
These are the Left Handed versions, to see the Right Handed please CLICK HERE.
These are the basic rasps for shaping work. They are relatively wide in proportion to their length giving you considerable cutting power. You will get surprisingly smooth finishes to your work. As a general guide you should chose a rasp which is 3/4 times longer then the width of the piece you are shaping.
As an example...
Left Handed Auriou Cranked Neck Curved Ironing Rasps
These are the Left Handed versions, to see the Right Handed please CLICK HERE.
These are very useful for working in small areas. The rasp is short and is curved along its length so you can enter your work easily.
The tang is cranked to allow knuckle clearance.
4 sizes and grains based on width:-
10mm wide Grain 12
15mm wide Grain 11
20mm wide Grain 10
25mm wide Grain 09
30mm wide Grain...
Left Handed Auriou Modellers Rasps
These are the Left Handed versions, to see the Right Handed please CLICK HERE.
These are similar to cabinet rasps but are not as wide relative to their length. This allows you to work in tighter spaces. They are for more delicate shaping work and complement the work done by cabinet makers rasps.
The 6" (150mm) grain 15 rasp is for making very fine refinements to your work whilst the 7"...
Auriou 4 in 1 Rasp
Flat on one side, convex on the other, with two stitches (grain 7 & 9). Use the finer stitch across the grain and the coarser stitch with grain when speed and close dexterity are needed. Useful for stickmakers and knife handle makers.
Auriou Albi Combination Rasps
These are the Right Handed versions, to see the Left Handed please CLICK HERE.
These are stitched on both sides with one "safe edge".
The rasp is thinner close to its tip to allow ease of entry into your workpiece. For flat and convex work only.
As normal, the longer the rasp, the coarser it is. We offer 2 sizes. The sizes shown are the rasp dimensions without the handle.
The...
Auriou Cabinet Maker's Rasps
These are the Right Handed versions, to see the Left Handed please CLICK HERE.
These are the basic rasps for shaping work. They are relatively wide in proportion to their length giving you considerable cutting power. You will get surprisingly smooth finishes to your work. As a general guide you should chose a rasp which is 3/4 times longer then the width of the piece you are shaping.
As an example...
Auriou Cranked Neck Curved Ironing Rasps
These are the Right Handed versions, to see the Left Handed please CLICK HERE.
These are very useful for working in small areas. The rasp is short and is curved along its length so you can enter your work easily.
The tang is cranked to allow knuckle clearance.
4 sizes and grains based on width:-
10mm wide Grain 12
15mm wide Grain 11
20mm wide Grain 10
25mm wide Grain 09
30mm wide Grain...
Auriou Curving (Chairmakers) Rasp
Called a curving rasp but also known as a chair makers rasp due to its usefulness for shaping the crest rail or seat of a chair or working any large concave surface. Michel Auriou also comments that this rasp is effective when working along the grain and is very useful in shaping cabriole legs.
250mm (10") overall with coarse grain 7 teeth for rapid stock removal.
One end is a tapered half-round...
Auriou Locksmiths Rasp
This is a very typical old French combination shaped rasp. It is called a locksmiths rasp and has a large knife shaped end and a rat tail end.
It is 250mm overall (10 inches) and is used to shape mortises or grooves, not just by locksmiths nowadays but used by sculptors.
Grain 9.
Auriou Modellers Rasps
These are the Right Handed versions, to see the Left Handed please CLICK HERE.
These are similar to cabinet rasps but are not as wide relative to their length. This allows you to work in tighter spaces. They are for more delicate shaping work and complement the work done by cabinet makers rasps.
The 6" (150mm) grain 15 rasp is for making very fine refinements to your work whilst the 7"...
Auriou Needle Rasps
1/2 round, flat, rat tail and knife shaped needle rasps, very fine grain (14) for detailing work.
Approximately 7¼" long with a 2¾" blade, these are well suited for making models or musical instruments and shaping keyholes or pierced carvings - anywhere a larger tool would be awkward or too aggressive.
Stickmakers love using these for detailing work on their sticks.
Auriou Rat Tail (Tapered Round) Rasps
Stitched to the tip! Tapered round rasp.
Great for shaping round mortises or for creating a spiral on a goblet stem. Use with twist action to utilise all the teeth.
We have a limited number of unhandled rasps at a reduced price, please see here.
Auriou Riffler Rasp - Half Round / Triangular
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Auriou Riffler Rasp - Knife / Spoon
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Auriou Riffler Rasp - Rat Tail / Oval
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Auriou Riffler Rasp - Rhombus / Brush
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Auriou Riffler Rasp - Thumb / Laurel
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Auriou Riffler Rasp - V Shape / Rectangle
These are hand stitched with a comfortable "fat" hexagonal barrel handle which allows you to use the riffler for long periods of time without discomfort or fatigue. Grain 14 is extremely fine and grain 10 is fine.
Auriou Roughing Rasp
This is the 'hog' that reduces your band saw blank to more closely resemble to the shape you want (think cabriole leg, guitar neck, gun stock, decoy duck blanks etc)
Flat and half round tapered section, grain 3. the rasp (excluding the handle) is 12" (300mm) long.
Available in left or right handed models.
The address position for holding your rasp is slightly skewed across the grain (just...
Chris Pye Set of 2 Rifflers for Wood
Set of 2 Chris Pye Rifflers, 7" in length.
Pfeil Canvas Tool Rolls
Pfeil offer high quality 8, 12 or 25 pocket canvas tool rolls for carving tools.
Connells 12 Pocket Leather Tool Roll
The Connell Leather Chisel Roll has 12 pockets, with top and tail design for better protection.
Will accept chisels up to 275mm (11') long.
Rolls up neatly for easier storage.
Made from soft moss backed leather for durability
Pockets reinforced with brass rivets. Ties for secure fastening.
Connells 8 Pocket Leather Tool Roll
The Connell Leather Chisel Roll has 8 pockets with top and tail design for better protection.
Will accept chisels up to 275mm (11') long.
Rolls up neatly for easier storage.
Made from soft moss backed leather for durability
Pockets reinforced with brass rivets. Ties for secure fastening.
Journeyman Handcrafts Canvas Tool Roll
Keep your carving tools protected and portable with this Journeyman Handcrafts tool roll made from heavy weight 16oz green cotton canvas.
Designed with 16oz cotton canvas, this pouch is made to last and will endure many years of hard use. It’s double stitched with a very strong bonded nylon thread which is water and rot resistant. Finished with veg tan drawstrings for longevity and wooden toggles...
Flexcut 19 Pocket Tool Roll SK200
Keep all your Flexcut tools in one convenient tool roll. Fits 18 unhandled gouges and 1 handle.
Note the tools are not included.
James Barry Double Sided Leather Strop & Paste
This double sided leather strop from James Barry measures 8" x 3" x 3/4". The UK sourced leather is 4.5mm thick and is bonded to both sides of a wooden block.
One side is coarse which is used to accommodate the James Barry Mirror Paste. This does not just polish to an amazing standard but also puts on that final hone to achieve a scary edge.
The size is ideal to compliment the...
Norton Cyclindrical Slipstone
Sharpening tools with curved edges like gouges requires slipstones (and patience). Getting the exact slipstone to match the profile of the cutting edge is difficult. However this slipstone has a wide diameter of 3/4" which is unlike most other slips.
This Norton India Stone is particularly helpful for working incannel tools such as firmer gouges. It is also handy for removing the burr on the...